Custom Query (122 matches)

Filters
 
Or
 
  
 
Columns

Show under each result:


Results (91 - 93 of 122)

Ticket Resolution Summary Owner Reporter
#129 fixed Discriminating between Anonymous Michael Halloran michelpons

Reported by michelpons, 12 years ago.

Description

In the attached log filen within Calculate I know that the UO gets temperature, pressure, partial mass flowrates from the MO connected to the inlet Port and then sets the same properties on the MO connected to the outlet Port before flashing the MO on the outlet Port. But all SetProp/GetProp calls are mentioned as being made on an anonymous MO. Without the source code of the UO, it would be impossible to know on what the UO acts. Even if the MOs are not named by the PME, which is a pity, could COLTT discriminate between anonymous MOs and mention an Anonymous_1, Anonymous_2 so that one could better follow the sequence?

#130 duplicate Repeated calls by COLTT on persistence interfaces Michael Halloran michelpons

Reported by michelpons, 12 years ago.

Description

I am using COLTT 2.1 Build June 16, 2012 enabled on a TEA Thermo System and a COUSCOUS Mixer in PRO/II 9.1. I start from a case file where the TEA Thermo System and one of its PP has already been declared and two material streams have been defined. Then I drop the COUCOUS Mixer on the flowsheet, connect inlet ports and the outlet ports and then I run the simulation which ends up with no error. Parsing through the log file obtained, I am puzzled by the following sequence:

COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistPropertyBag

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStorage

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStreamInit

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStream

COLTT <CO1> : Return from QueryInterface - Succeeded COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistPropertyBag

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStorage

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStreamInit

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStream

COLTT <CO1> : Return from QueryInterface - Succeeded COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistPropertyBag

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStorage

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStreamInit

COLTT <CO1> : Error returned from QueryInterface - 0x80004002 COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStream

COLTT <CO1> : Return from QueryInterface - Succeeded COLTT <CO1> : Call to QueryInterface

Requested Interface : IPersistStream

COLTT <CO1> : Return from QueryInterface - Succeeded COLTT <CO1> : Call to IPersistStream.Save COLTT <CO1> : Return from IPersistStream.Save - Succeeded

It seems there are repeated calls on the same interface by COLTT and that the failure to find this or that interface on the UO is not accounted for by COLTT which repeats on and on the same calls. This sequence seems to occur several times and since the overall logging takes quite longer than the simulation wothout any log, I was wondering if unnecessary calls were made by COLTT and if so could be discarded.

#131 Not Reproducible Save called by COLTT not by PME michaelhalloran michelpons

Reported by michelpons, 12 years ago.

Description

I am using DWSIM in which the CAPE-OPEN C++ Sample mixer is connected to two inlet streams and one outlet stream. I am just opening the case then clicking on the icon representing the UO, then exiting from DWSIM WITHOUT saving the file when asked by DWSIM. It gives a rather short log file where the most surprising point is that, at the end of it, one sees a call by COLTT on IPersistStream.Save while there is no such call made by the PME on the UO. I wonder why such a call is made and succeeds.

Note: See TracQuery for help on using queries.